Partner Post: Top 5 Tips for Hot Weather Exterior Painting

June 29, 2017 Dunn-Edwards Corporation

This content was republished with permission from Associa Advantage partner, Dunn Edwards Paint. Associa Advantage partners provide savings on household goods and services used by Associa community homeowners and associations.

When starting an exterior painting project, mild temperatures are not only preferred by the painting contractor or applicator, but the paint as well. Just as cool, damp conditions adversely affect the performance of paints, so can extreme hot temperatures. Ideally, most latex paints should not be applied when air and/or surface temperatures are below 50° F or above 90° F. We have included precautionary tips that may help mitigate some of the issues attributed to hot weather painting.

Latex Paint Film Formation

Latex paint consists of dispersed pigment and resin, along with some additives and liquid, which is mainly water. When the paint is still in its liquid state, the particles of pigment and resin are evenly distributed and spaced out. After application, the water begins to evaporate, and the particles of pigment and resin come closer together. As the remaining liquid evaporates, the resin particles gradually become more densely packed, causing them to fuse and bind the pigment into a continuous film. This process is called coalescence.

Paints that dry too fast can have film defects similar to what is seen with mud cracking (dried paint film resembles the deep irregular cracks that form in dried mud). Additionally, if you apply paint through airless spray application during periods of dry warm weather, a phenomenon called dry spray can occur. This will result in a finish that is grainy or sandy and uneven in sheen and texture.

Open time refers to the length of time (workability) that a paint can be easily applied or spread onto the substrate, or surface. If the substrate is too hot or air temperature is too high, the ability of the paint to flow and level will be negatively impacted, leaving unsightly brush and roller marks. There may also be excessive lap marks and poor sheen uniformity in the dry film.

Precautionary Tips for Hot Weather Exterior Painting

1. Check the weather forecast. Determine the weather pattern for the days you are going to paint. If the temperature is going to rise above the maximum mark during the application and drying phase, it will be necessary to take the following steps to ensure there are no application issues or damaging effects to film formation.

2. Follow the shade. In the summer, the rule is, don’t paint in the sun and follow the shade around the house or building.

3. When humidity or dew points are low, begin the painting project earlier in the morning when possible. During midday, when the sun is at its highest, avoid painting. As long as conditions allow, begin painting again in the late afternoon hours making sure to follow the shady areas.

4. Take special precautions to cover opened paint containers, as direct sun and high temperatures will increase the tendency of the paint to skin in the roller tray or in the container.

5. Just as it is necessary for humans to hydrate during hot temperatures, it may be necessary to add up to 4-6 oz. (per gallon) of clean water to maintain workability of latex paints.

About the Author

Dunn-Edwards Paints® has produced and sold premium paint products for more than 90 years and is the #1 Choice of Painting Professionals based on an independent study where licensed painting contractors in Los Angeles, San Diego and Phoenix overwhelmingly selected Dunn-Edwards Paints as the paint they would use on their own homes. With 129 company stores in California, Arizona, Nevada, New Mexico and Texas, and more than 80 authorized dealers throughout the Southwest, Dunn-Edwards is one of the nation’s largest independent manufacturers and distributors of architectural, industrial and high performance paints and paint supplies. The company is dedicated to preserving and protecting the environment, and produces its coatings in the world’s first and only LEED® Gold-certified manufacturing plant. Based in Southern California, the company is composed of approximately 1,500 employees. For more information, visit www.dunnedwards.com.

More Content by Dunn-Edwards Corporation
Previous Article
Partner Post: Use These 3 Plants to Engage Your Kids With Gardening
Partner Post: Use These 3 Plants to Engage Your Kids With Gardening

Find out in this post which plants will make gardening fun for kids so you can enjoy quality bonding time w...

Next Article
5 Indispensable Tips for Home Safety During Vacations
5 Indispensable Tips for Home Safety During Vacations

These tips will show you how to protect your home and preserve your relaxation while you're on vacation.